1766 UM001 EN P PDF

Publication UMA-EN-P – November Table of Contents . User Manual UM to assign an IP address to the MicroLogix. controller. Publication INC-EN-P – October Important . Manual UM .. publication UM, for more information on surge suppression. rm_-en-p – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Document Number IN UM

Author: Nigore Mik
Country: Gabon
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 14 May 2012
Pages: 132
PDF File Size: 13.87 Mb
ePub File Size: 7.98 Mb
ISBN: 247-4-33291-529-1
Downloads: 46034
Price: Free* [*Free Regsitration Required]
Uploader: Nigal

Follow these steps to install your controller using mounting screws.

United States Contact your distributor. Do not touch circuit components inside the equipment.

IN – Rockwell Automation

Make sure your controller is spaced properly see Controller Spacing on page 12 for more information. The controller can be mounted to ENx7. The examples and diagrams in this manual are included solely for illustrative purposes. No patent liability is assumed by Rockwell Automation, Inc. For more information, contact your local distributor or Rockwell Automation representative, or visit http: Drilled fragments that fall into the controller could cause damage.

The drain wire and foil shield must be grounded at one end of the cable. This could cause an explosion in hazardous location installations. For example, when using a real-time clock RTC. Installation Assistance If you experience a problem within the first 24 hours of installation, please review the information that’s contained in this manual.

1766-IN001 – Rockwell Automation

AC powered products must be connected to the secondary of an isolating transformer. The input and output terminals of the MicroLogix controller are um001 for the following spade lugs. Industrial Automation Wiring and Grounding Guidelines The Belden cable has two signal wires black and clearone drain wire, and a foil shield.

  BIMCO SHIPMAN 98 PDF

Power Loss in Transmission Lines. Failure to remove the strip before operating can cause overheating. The interior of the enclosure um0011 be accessible only by the use of a tool. Additional noise immunity can be obtained by routing the cables in grounded conduit.

This equipment is supplied as open-type equipment.

Rockwell Automation

Outside United States Please contact your local Rockwell Automation representative for the return procedure. Follow these guidelines when you handle this equipment: The terminals will accept a 6.

Follow these steps to install your controller on the DIN rail. Leave the protective debris strip attached until you are o wiring the controller and any other devices. Do not touch connectors or pins on component boards.

Scripting must be enabled to use this site.

Replace the battery when the controller is powered on. Soal meeting 9th Eh of speech: Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

New Product Satisfaction Return Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. B mm 7. Make sure that the placement of the controller on the DIN rail meets the recommended spacing requirements see Controller Spacing on page 12 for more information. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility umm001 other environments due to conducted as well as radiated disturbance.

Once wiring is complete, remove protective debris strip. Identifies information about practices or 176 that can lead to personal injury or death, property damage, or economic loss.

Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation. Wiring Your Analog Channels Analog input circuits can monitor voltage signals and convert them to serial digital data as shown in the following illustration.

  CARTA A MENECEO PDF

Hook the top slot over the DIN rail. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect support programs.

Wear an approved grounding wriststrap. Do not touch the connector pins or other sensitive areas.

Failure to remove strip before operating can cause 176. It must be mounted within an enclosure that is suitably designed for those specific environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts.

Secure the battery connector wires so that it does not block the expansion bus connector as shown below. Once wiring is complete, be sure the controller is free of all metal fragments before removing the protective debris strip.

Holding the controller, pry downward on the latch until the latch locks in the open position. Output group to output group isolation Verified by one of the following dielectric tests: Use a static-safe workstation, if available. Linea centrale della guida DIN. Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.