ASTM B – Designation: B /B M – 01 Standard Speci?cation for Copper -Nickel-Tin Alloy, C. This standard is issued under the fixed designation B /B M; the number . ASTM designation and year of issue (B/. B M. ASTM B attains the requirements for copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C, UNS C alloy. Such Sheet or.
|Published (Last):||28 April 2010|
|PDF File Size:||15.78 Mb|
|ePub File Size:||18.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
The values stated in each system are not exact equivalents; therefore, each system shall 1 This speci? C M20 H01 H02 H04 H06 H08 as hot-rolled hard half hard hard extra hard spring 48 56 67 80 89 95       65  73  82  94    Slabs are meant for rolling sheets, g122, plates, etc.
Cupro Nickel (UNS C, ASTM B)
Copper plus adtm with speci? Historical Version s – view previous versions of standard. NOTE 2—Because of the discontinuous nature of the processing of castings into wrought products, it is not always practical to identify a speci?
Nickel additions in these alloys allow designers to benefit from attractive color options ranging from light rose to silver. Steel ingot is the cast metal with porosity and blow-holes. C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 42 55 58 71 73 78       62 67 72 85 90 91       C Phosphorus at 0.
A superscript epsilon e indicates asmt editorial change since the last revision or reapproval. A slab, also from ingot, has a rectangular cross-section, with an area of at least cm2 and width aztm least three times the thickness. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
Offer on Fasteners Sitemap. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? ASTM B Rolled Bars are known for the long subsequent processing they undergo secondary and tertiary processors, until the final end products are produced.
70-30 Cupro Nickel
C are required, see appropriate table. C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 38 47 56 67 72 76       56 63 70 79 84 87  aetm     C 6 80 Grain size is the standard requirement for all products in the annealed tempers.
Cupro Nickel Alloy with small amounts of iron and manganese improves corrosion resistance in high-velocity waters, including seawater. A number in parentheses indicates the year of last reapproval. C 48 55 63 73 79      63 70 77 87 91      Current edition approved May 10, C and C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard ast hard hard extra hard spring 45 58 66 75 80 84       65 72 80 88 b1222 94    axtm   B Scale 68—82 80—90 87—94 89—96 Super?
The minimum weight of the composite sample shall be g. The bloom has a square cross section. Last previous edition B — The second is the electric arc furnace EAFwhich primarily uses steel scrap as the raw material.
ASTM B Copper Nickel Sheet Plate Supplier · B C/C
Originally published as B — 39 T. C 5 70 The following alloys are covered: This specification also contains information on the standard tempers for and tensile strengths of hot-rolled, cold-rolled, and annealed tempers.
Link to Active This link will always route to the current Active version of the standard. The first stream is referred to as the integrated mill stream, which uses mostly iron ore to feed a blast furnace, which in turn supplies hot iron to a steel making operation. C 9 70 10 Both processes can produce ingots which are rolled into blooms or billets or strand cast blooms or billets.
Cupro-Nickel are among the most attractive, durable and versatile copper alloys available. C, C, C, C, and C for use as tube plates in surface condensers and heat exchangers are covered by Speci? Required properties for other tempers shall be agreed upon between manufacturer and purchaser at the time of placing the order.
It is informational only and not an official part b1122 the standard; the full text of the standard itself must be referred to for its use and application. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. When all elements in Table 1 are analyzed, their sum shall be as follows: If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee n122 Standards, at the address shown below.