HT12D HT12E PDF

This project has been design around HT12E and HT12D encoder / decoder chips from Holtek. With jumper selectable address on the receiver. The HT12E Encoder ICs are series of CMOS LSIs for Remote Control system applications. They are capable of Encoding 12 bit of information which consists of 8. By using the paired HT12E encoder and HT12D decoder we can easily transmit and receive 12 bits of parallel data serially. HT12E simply converts 12 bit.

Author: Zutaxe Kakree
Country: Bahamas
Language: English (Spanish)
Genre: History
Published (Last): 20 January 2011
Pages: 468
PDF File Size: 16.8 Mb
ePub File Size: 5.8 Mb
ISBN: 607-8-45706-218-4
Downloads: 19231
Price: Free* [*Free Regsitration Required]
Uploader: Arashisida

Add decoupling caps close to the IC. The encoder HT12E is capable of encoding information comprising 12 bits in total; 8 address bits and 4 data bits.

ht12d & ht12e

Pabitha Pabi 25 June at Email Required, but never shown. Did you really need to post that many images without the full URLS, no less? Posted by Nigel Ut12d at All is working now, thanks to all.

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. I’m working on a ht12f circuit. Using the Raspberry Pi to control. Keep IC’s close toegether and imagine that it is a printed circtuit ht12s layout. Thanks for all your awnser, after studying a little bit into the RF module I found out my problem, the left side of both encoder and ht12v are the Address PIN, which means they will only communicate if those addresses are the same, that was what I was making wrong, I ht12dd them all at 1 and changed the resistors in them both cause the TX need to have 20 times the resistence of the receiver, in hht12e words 50k and 1M resistors.

  GITARRENBUCH FR ANFNGER PDF

For fun here is a free tool to help design, layout and simulate. Best practice of using the breadboard is to use short solid wire leads and neatly connect flush to the board without large inductive loops. I see you do not have jumpers to join each side of the power rails. Tony EE rocketscientist 62k 2 21 The output from the encoder can be used in various ways; for example to feed a Radio Frequency or infrared transmitteror it could be directly connected to a decoding processor.

Guilherme Garcia da Rosa 2 3 7.

Use staples for hr12e and ground rails. Don’t use wire with thick insulation. ClearAll set A ports to ”. It could be said that this is a very convoluted way to use this technology but it was really useful to experiment and prove that it was possible.

The outputs from the HT12D decoder can be used to switch connected logic circuitry or other attached devices via suitable interfaces. Number 99 entered quits the script. I know but, and I’m going to sound like Olin here it should be easy to see how inconvenient it is, even for a new user.

Home Questions Tags Users Unanswered. So, you are saying, when you grounded all the pins on the left of HT12D and 12E, it worked? Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that ht12r have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

With the possibilities of using multiple decoders HT12D all ‘listening’ on their individually configured addresses it is possible for the Raspberry Pi or Arduino to control both the address values and control the use of the data pins. Note there is a gap on both sides down the middle for the Blue and Red outer rails. Trigger send trigger pulse. I’ve never tried this before but looks ok.

  CALENDAR BISERICESC 2014 PDF

I have included a simple Python3 script below, which prompts the user to enter a number between 0 and 15, and using Binary Coded Decimal, sets the AD8 – AD11 pins to convey the user entered number correctly. I wondered whether these processors were still available – they are! The transmission of the data stream can be over an RF link or direct connection using 2-core cable. I also thought it would be a great opportunity to fully investigate the operation of the two processors to help me better understand how I might use these in the future.

I began to think about how I could use this technology with the current range of micro-controllers such as the Arduino and the Raspberry Pi, together with other potential uses. Yah but I agree. Post as a guest Name. Newer Post Older Post Home.

I htt12d experimented further with this, connecting LEDs to the HT12D decoder data pins to ensure the transmitted and received data is presented correctly. Sign up using Facebook.

I haven’t drawn any circuits for this as the interfacing is straight forward as both the Raspberry Pi and the HT12E operate at 3.

ht12d & ht12e | EngineersGarage

Avoid long jumper wires at all costs. The GPIO pin acting as the trigger function needs connecting via an inverter circuit. Try to get thin solid wire 24 AWG I believe. Sign up or log in Sign up using Google.

And the picture of the circuit done: Remember I said check power?