This is a Kenwood VHF repeater, model number TKR This is a 32 ch, 50 watt repeater that operates in the Mhz range. Repeater is capable of both. Find great deals for Kenwood Tkr Repeater VHF 16ch MHz 50 Watts. Shop with confidence on eBay!. TKR) TCXO modules, % duty RF power amplifier output is 50W (at 50 % duty) a TKR is 40W (at. 50% duty). make Kenwood’s TKR/
|Published (Last):||6 December 2014|
|PDF File Size:||7.63 Mb|
|ePub File Size:||9.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Then we bought 2 more to replace our aging Aerotrons. We use these repeaters in commercial radio sites.
Kenwood Tkr-750-1 Repeater VHF 16ch 146-174 MHz 50 Watts
Email Subscription You are not subscribed to this review. However, since the TKR runs on 13,8 volts, it is easy to use just any heavy-duty power supply.
Otherwise it is a very nice machine. Modem bps, extra stability in high RF environments, includes interface cable.
Includes one cable for radio connectivity. Specify DC current settings at time of order. I had to modify the CAT to get the audio up to where it should be. Just want to let folks know that hams may be better off getting the low split K2 version, just FYI. Price is very reasonable, and would buy one again. Just asking for it to be blown out as I’ve seen time and time again. Built in mini controller is nice. Locking cabinet, providing 40 RU vertical mounting, solid front door, louvered rear door.
We’ve had the pre amps and TRK’s in service about 2 years with no issues. When I tkr-570 done programing the repeater I checked kenwoof rec and it was 1.
Clean, crisp audio otherwise. Item is an option and kemwood be sold separately. If you have any questions, problems, or suggestions about Reviews, please email your Reviews Manager.
Base Station & Repeater
They seem as reliable. These have a built in DTMF controller, which can be configured to control internal functions, or drive external accessories or relays. Programmed repeater the on the bench and installed on site it has worked great without any changes. We have 7 of these repeaters on our linked repeater system, they have been operating flawlessly for 5 years or so.
In the front part of the rec there are 5 coils you have to tune with a signal gen. Includes equipment installation, hardware, cabling and wire management materials, and cushioned shipping crate. The 25 pin connector gives you everything you need.
My Subscriptions Subscriptions Help. We purchased the models, kenwoof the higher split should work fine in the ham bands. Let the duplexers filter out some of the noise and protect the pre amp. Includes two cables for radio connectivity and an internal antenna relay. Could use a little more fan, but we have never had one go down. I built some 10 db pre amps and put them between the receiver input and the duplexers.
Plus why amplify noise before the duplexers? For use with voting systems, supplies Ohm balanced 2-wire audio, occupies 1 RU. And yes, I checked the alignment and it was correct. Ktr-750 it out and you have the same sensitivity of the Kenwood. tkr-7550
The Kenwood software is excellent. Runs just fine and no heat issue. Includes tlr-750 pre-drilled openings and grommets. Cabinet Solid Floor Panel. That takes about 5 minutes to do, but should be done for best sensitivity. Audio is fantastic, and it is easy to implement an external controller or accessory.
Modem bps to be used with LTR controllers, includes interface cable. Optional for situations where extra protection during transportation is required. Contact the site with comments or questions.
Patent and other rights reserved.
Kenwood TKR / TKR Repeater Base Units United Radio Communications Chicago
Then I retuned the coils and got it down to. Work great, same sensitivity as the GE IIs. Cabinet Fan Top Assembly. The rec goes down to.
Set at 30 watts input to the duplexers. As for sensitivty I was disappointed. Software is very easy to use and a breeze to program. New to Ham Radio? Programmation is also a charm. Cabinet Solid Top Panel. Excellent performance, even with less than krnwood filtration