LG Display Co., Ltd. Date: TO: TOSHIBA CORPORATION. DATE: ‘ Specification of ” TFT/LCD. MODEL: LPX08 (TLAD). S.P. Yang. Full text of “Datasheet: Panel LG Philips LCD LPX08 TLA2 0” OLED panel application: Datasheet, inventory and accessory! @ Global. Datasheet Panel LCD s LCD model LPXA2 inch for Laptop | Feature:Landscape type.

Author: Dijin Tygokree
Country: Armenia
Language: English (Spanish)
Genre: Software
Published (Last): 4 July 2018
Pages: 370
PDF File Size: 20.90 Mb
ePub File Size: 20.25 Mb
ISBN: 275-1-31405-356-2
Downloads: 35594
Price: Free* [*Free Regsitration Required]
Uploader: Fautaxe

LP150X08-TLA8 Datasheet PDF

And after fading condensation, smear or spot will occur. This is subject to change without prior notice.

Viewing angle is the angle at which the contrast ratio is greater than For example, remember the country or language you selected to visit the pages, and are not used for marketing purposes. The design of the inverter must have specifications for the lamp in LCD Assembly.

For more information see FIG 2. Contrast Ratio CR is defined mathematically as: It eatasheet recommended that they be stored in the container in which they were shipped.

The LP1 50X08 is intended to support applications where thin thickness, low power are critical factors and graphic display are important. If you not change browser datashheet, you agree to it. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.

  785GM P45 PDF

Full text of “Datasheet: Panel LG Philips LCD LPX08 TLA2 0”

You can control your cookies through your browser. In addition to accept or reject the use of certain dtasheet through pantallasdeportatiles. Those that have been installed before changing the settings remain in your computer and you can delete them using the configuration options of your browser.

And please do not rub with dust clothes with chemical treatment. This LCD employs two interface connections, a 30 pin connector is used for the module electronics and the other connector is used for the integral backlight system.

s LCD LPXTLA2 Overview –

Sufficient lp150x088 to the electromagnetic interference shall be done by system manufacturers. The matrix employs a-Si Thin Film Transistor as the active element. These cookies are managed by third parties, which can use these tools to restrict the use of these cookies.

Dataaheet text of ” Datasheet: Please avoid floating state of interface signal at invalid period. So all the parameters of an inverter should be carefully designed so as not to produce lp150x80 much leakage current from high-voltage output of the inverter.

However, they can be used with several different purposes ranging from remembering the login information or what is in your purchase order. It shall help increase the lamp lifetime and reduce leakage current. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. This site uses cookies and similar technologies.


In combination with the vertical arrangement of the sub-pixels, the LP1 50X08 characteristics provide an excellent flat display for office automation products such as Notebook PC. Signal Timing Specifications This is the signal timing required at the input of the User connector. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency datasheeh from its harmonics in order to prevent interference.

Otherwise, the lamps may not be turned on.

Do not expose the module to sunlight or fluorescent light. Temperature and relative humidity range are shown in the figure below. Horizontal Blanking 4 1 ! Condensation makes damage to polarizer or electrical contacted parts. The voltage above V s should be applied to the lamps for more than lp1550x08 second for start-up. Mechanical Characteristics The contents provide lp150x8 mechanical characteristics for the model LP1 50X When the protection film is peeled off, static electricity is generated between the film and polarizer.

For additional information see FIG 3.